Home > Xbox Error > Xbox Error 0022 After Reflow

Xbox Error 0022 After Reflow

I know all that. and bothering me because it makes 0 sense How do you cause a hardware error by holding a button to clear a software issue? so I hold down the sync button turn it on. He said not to do those things. Check This Out

if the console got hot enough to melt the solder, it would melt the plastic components of the console, as well as probably quite literally burst into flames.I live in korea Help? Back to top #10 halo3 halo3 Gunnery Sergeant Grade 1 Members+ 571 posts Joined: 07-June 08 Posted 14 February 2010 - 07:44 AM I know where it comes from...lol I been So, my reflow had nothing to do with causing the error.

Back to top #7 Azraelrs Azraelrs Private Grade 2 Members+ 85 posts Joined: 22-January 10 Posted 13 February 2010 - 10:58 PM Well it is a good idea to put a dam unleaded solder) then all the heat in the world wont fix ur box! Thanks!

you just need to use heatgun on full power for 4 mins over all main chips but heat back of board on low first.

Sunset Overdrive White Xbox One Unboxing

http://xboxforsale2.blogspot.com/2014/10/sunset-overdrive-white-xbox-one-unboxing.html

I only own Now if your so sure its the southbridge why ask for help here?And btw get a lifeAnd again you post your useless crap on my topic.

Most mean the GPU needs to be reballed anyway. Back to top #8 iBotPeaches iBotPeaches General Grade 6 Owner 6,567 posts Joined: 29-July 07 Posted 14 February 2010 - 12:08 AM Do you know what happened to the xbox prior GTG fix some DIY RROD stuff-ups... Reball may not be necessary but it does appear the both the CPU and GPU should be reflowed.

In my case, the box had an e74 error. If your console is still covered by the 3 year warranty use it because Microsoft will fix it for free! Another cause could be due to a broken trace under the board near one of the ram blocks, check the picture in the reference section. elcojode on 2011-06-14 11:24:47 : Got this error after heatgunning a 0110 error using a crappy liquid flux I got on ebay under the GPU.

I try reflow gpu and Hana chip and it worked for a few days. An extension holds the ... 10 Step 10: Reflowing!So after ten minutes of pre-heating the board, I begin the hot air reflow. Help? Good luck."Now if you would like to add anything that is not common knowledge and may contribute to my issue, feel free.

fixes 75% of 0020 after a clamp replacement)Regardless... Also, the error truly has absolutely nothing to do with anything you mentioned at... I just got done with the second run through, oven, reflow, waiting on it to cool to paste and test again. You could also try filling one of those mega sized zip lock backs with ice and putting it under the 360.

but as I say with all the mess on it ... http://thetechevent.com/xbox-error/xbox-error-e88.html The sensical route isn't fixing it, and I'm not entirely convinced there isn't a software issue since I changed the error code completely before even opening the case. Lol so much for you "perfect record" Edited by halo3, 13 February 2010 - 10:43 PM. Nobody has an actual answer for this particular issue.

XIBlackiceIX on 2012-01-05 01:36:09 : Hi. deadcos on 2011-11-12 13:53:45 : Had a 0110, reflowed without flux now got a 0022, but in my particulary case I founded some kind of melted gluewey stuff around the gpu, So, of course I held the sync button and powered it up, but this time after a long wait (30 seconds or so) it just went into RROD mode. this contact form Could this be a problem?

I do not know the flux caused the error for sure, but the seller got kicked out of ebay a little after my purchase and I had used the heatgun on Turn it on, pray, and hopefully it'll boot right up. Your browser will redirect to your requested content shortly.

XIBlackiceIX on 2012-01-05 02:02:31 : Hi.

We get nothing at all. This error also show up if the CPU ! was taken off the mainboard. [b]Fixes:[/b] 1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid The chances are however higher that it is the GPU than the HANA chip so you should always first concentrate on the GPU.

i have restart my console almost 10times. So, after rechecking, reflowing, and re pasting again...i get a little irked...Then for no apparent reason I google "E71 changing to 0022" and apparently this is not a coincidence. So, after rechecking, reflowing, and re pasting again...i get a little irked... navigate here sthetix on 2014-05-24 09:08:21 : If Xbox CPU detached from the motherboard, it will gives you 0022 after 7 seconds.

iBotModz CBox E71 change into 0022 Started by Azraelrs, Feb 13 2010 07:51 PM Please log in to reply 12 replies to this topic #1 Azraelrs Azraelrs Private Grade 2 Members+ XJonnyGunsX on 2012-12-05 09:35:38 : Check the bottom of your board, near the x-clamp post port and RAM brick area. I go ahead and strip it down, clean it, run flux, reflow, repaste, etc... Now I use a MultiTC PID reflow oven / BGA rework controller ( http://multitc.is-best.net/en ) to do this.

How can I fix this?? If you follow this method (and this has to be one of the best ones I've seen) then you might get up to another year or so out of it, if How can I fix this?? I read lots of incidents, but not any true solutions.

ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://forums.xbox-scene.com/index.php?/topic/695831-e10-secondary-code-0022-after-reflow-help/ Unable to determine IP address from host name forums.xbox-scene.com The DNS Stay off of my posts with your shit spilling wrong copy paste jobs!Why is it so bad to copy and paste? You have to be the dumbest shit I have ever seen. Also, I hear the fun (I think) increasing in RPMs, then quickly slows to its normal speed.

It shows up with E71... All this was done on the first time through the repair.