Home > Write Error > Write Error Rate At Preamp

Write Error Rate At Preamp

I won't pay more than I earn if they don't show what they've been studying more then me.louis wrote:It seems to be a food chain ..starting from the ones building those This attribute is mainly limited to the notebook (2.5") drives. If it's inside the ROM code, it's clear that If I flash bogus data, the chip is bricked and requires external flashing method. This way anybody can become the technician if stuff goes bad.What gets me riled up is these noobs coming around here. Check This Out

And no it is not worth fixing hard drives. If someone knows...the VSC commands are processed by the ROM software...or there's a boot loader inside the MCU? You clearly have no clue about what is really involved in DR and (just like all other novices in DR) you want everything for free with your demands and requests. The Mod which contains the real model name it's on the SA.

Three values are associated with each S.M.A.R.T. They say they are interested in data recovery operations. alma83 Мастер (1281) 2 года назад Проверь прогой HDD Tune Pro в разделе "Здоровье"Для системы надёжней брать серию WD Blue. This may be caused by problems with disk surface or the read/write heads.

I assume it is generated by the OS loaded by MCU, but is that table accessible without the OS accessing the SA?Ok I found by myself.It seems that Action Code 0xd Tried the demo tool called wdr-4.0. Is this thing on its last leg? The system returned: (22) Invalid argument The remote host or network may be down.

I assume that with RAm loaded OS you can the re-flash the BIOS, if the VCM's are handled by the OS. "why are you trying to build software". The "function codes" (in 512 bytes key) spreads from 0..to n. Please try the request again. Recommendations Although this parameter is not considered critical by the most hardware vendors, degradation of this parameter may indicate electromechanical problems of the disk.

Most common S.M.A.R.T. The T.E.C. Disk-to-host transfers are protected by CRC error detection code when Ultra-DMA 66 or 100 is used. on these drives, it is a real PITA.All this, assuming you will do the head swap flawlessly, which itself is highly doubtful (no offense meant). _________________Northwind Data Recovery - GreeceWD Trusted

Are you even sure it's headstack related ? To start viewing messages, select the forum that you want to visit from the selection below. Low values in absence of other fault indications point to the disk surface problem. More,what's funny, they hope to catch some info form real pros, which share their knowledge for free.Regarding my software development I've already implemented the ROM read feature.

At the end who can check them that it was what they say. his comment is here You may have to register before you can post: click the register link above to proceed. So..I found another guy which seems to be affected by the same problem like me. You can also include a comment.

Maximum values are typically 100, 200 or 253. Raw values are typically listed in hexadecimal numbers. Top louis Post subject: Re: WD2000JD problemPosted: February 28th, 2013, 16:37 Joined: August 22nd, 2011, 15:43Posts: 214Location: Romania Back in business.I went with it at the begging of this contact form It's out of warranty, and not really worth spending cash to get fixed.

It runs on windows 7. I doubt the issue is a defect in the PCB components.You... I won't pay more than I earn if they don't show what they've been studying more then me.

Raw value indicates the exact number of such sectors.

Top Michael.Reilly Post subject: Re: WD2000JD problemPosted: August 25th, 2011, 15:17 Joined: September 24th, 2010, 18:32Posts: 35Location: Louisville, KY louis wrote:Tried to clean the contacts. Lower value indicates more events (errors). If no other (critical) parameters report a problem, hardware replacement is recommended on mission critical systems only. To have the full control.

I've seen a MHDD script reading that table with a VSC cmd (0x0D)...with a param of 0x06 for marvell chip or 0x0d for royle. So you say it's 100% true that if I flash some bogus data inside the ROM, then I'll have the possibility to re-flash it again with the same VSC commands, using G-sense error rate Indicates if the errors are occurring attributed to the drive shocking (either due to the environmental factors or due to improper installation). navigate here Top Michael.Reilly Post subject: Re: WD2000JD problemPosted: August 24th, 2011, 18:54 Joined: September 24th, 2010, 18:32Posts: 35Location: Louisville, KY louis wrote:Some time the BIOS shows "WDC ROM MODEL-BUCCAN".see

It has an option to check the Heads on reading from SA. Top louis Post subject: Re: WD2000JD problemPosted: March 5th, 2013, 14:23 Joined: August 22nd, 2011, 15:43Posts: 214Location: Romania louis wrote:Can you tell me what the "zone table" or Only that I don't know when to read the 128kb bios or 196kb version, and who said how many times I can read the rom log.Quote:...ending with the fool which pays Despite your opinions about professional data recovery and this perception you have of it, without using some professional service you are not going to get anything resolved.