Home > Western Digital > Western Digital Controller Board Replacement

Western Digital Controller Board Replacement

Contents

Reply Powering of the device is a very common problem with USB devices and it has been traditionally singled out as the cause behind such disconnect symptoms. So, here is my workaround without having to spend $$$ on recovery. The intermittent hangs/freezes of 10-60 seconds were driving me nuts over the last month. Sign in to add this to Watch Later Add to Loading playlists... Source

It tests for very many things, so also worth a try to see what it says for you. my old hard drive 2.0 gives speed 20-20mbs. and it's happening to a lot of people it seems... If it still happens, the bad news is that this is likely a disk controller error, which is especially problematic since nowadays disk controllers are built into the Motherboard.

Western Digital Controller Board Replacement

Please try the request again. PhoneMan 2011-10-29 07:06:10 UTC #4 I get those errors at times also. The two best workarounds are: a) Use a powered USB 3.0 hub that has a good charger. What should I do?

Here's the report: Verifying volume “Photos”Verifying file system.Using live mode.Performing live verification.Checking Journaled HFS Plus volume.Checking extended attributes file.Checking extended attributes file.Checking extended attributes file.Checking extended attributes file.Checking volume bitmap.Checking volume what's happening is the harddisk is being turnoffed and not being turned back on. I had used it first on my XP, and then wanted to use it with my windows. Western Digital Smart Error Loading...

The system had two hard-drives, and the older hard-drive was seemingly working just fine, even with the same SATA cable and connected to the same slot on the Motherboard. Pcb Controller Western Digital If this occurs on an external hard drive, connect the drive to another USB of FireWire port on the computer. It's not easy to use, as for best use you need to burn it to it's own CD-R, but it literally Fixed the problem for us. Have you tried on another computer with a different USB3.0 controller?

Jim Home Categories FAQ/Guidelines Terms of Service Privacy Policy Powered by Discourse, best viewed with JavaScript enabled Support Downloads Knowledge Base German Spanish Italian French Log In The driver detected a Western Digital Error 0223 Feel free to leave comments if you are still struggling with this issue, and I will try to answer. btw i don't need RAID for mine so if you do... The drive works fine in a USB 2.0 port, but I have no other USB 3.0 controllers to test it on.

Pcb Controller Western Digital

I was able to pick up 8 GB of Gamer grade memory for $25 (after rebate), so that is another bonus with upgrade. I'll try replacing the sata tomm… Asad Dec 10, 2012 @ 00:09:32 Hi Adi, I just wanted to thank you very much for posting this solution. Western Digital Controller Board Replacement I have an Asus U36D notebook and struggled with this problem for a year! Initio Default Controller Western Digital I most likely have to downgrade my Fresco Logic drivers!

In order to fix this issue, update the firmware for the USB 3.0 Hub's controller. this contact form Any help would be appreciated.  Thanks in advance... The workarounds your are suggesting are well known and it is worth mentioning them. Reply You may be having a completely different issue, but since you mention nothing about your configuration I can't guess. Initio Default Controller Western Digital Windows 7

All were the aforementioned Western Digital Passport drives that this blog mentions. Everything works fine except those few event errors. Fantastic. #19 | Written by perry about 3 years ago. have a peek here cheers kiwikev #16 | Written by KiwiKev about 3 years ago.

The "Generic USB Hub" you have on the list may indicate that you have not installed all drivers necessary and are good candidates for what you are looking for. Western Digital I/o Error I think it doesnt, but im not sure. Reply Hey I found my solution to the problem, I know this thread is old but this just happened to me yesterday on my wd external hard drive.

Save your draft before refreshing this page.Submit any pending changes before refreshing this page.

I left SmartWare on my system for now. Read the release notes and perform the relevant update. Reply I have a Probook4520s and got a My Passport drive WD3200ME-01 model. Western Digital Error Codes I don't know if the issue is the HDD's, I surely hope not because that means we our out all of that data.

Very handy, and then you have up to 28 days to put your real key in and activate. I am just worried about losing data. These are available free from manufacturers web-sites, if you know the brand, or generic HDD utilities are available from download.com. Check This Out The best and most straightforward solution is probably to disassemble the case, take out the 'raw' hard drive, and plug it directly into a system which has easily accessible SATA ports.

To save the day for anyone with the same problem I have made a backup of this working driver! Both work great! #49 | Written by stathis about 3 years ago. If the problem persists across reformatting, then you need to have the hardware repaired.6.3k Views · View Upvotes · Answer requested by James MartinAnonymousWritten 12w agoVia :Error in RAID Configuration bjcreativeFOUND This is an operating system limitation detailed in Microsoft Knowledge Base Article 184006..

Reply sagardiaro, my system with 3.0.100.58 can go into hibernation mode or sleep without any problems cropping up with the USB3 port. #58 | Written by Rick about 3 years ago. If the hard drive or data cable is physically damaged or defective. Adi R Jan 15, 2012 @ 13:03:56 You are on the right track, but this one is super nasty issue, sorry. Contact AsRock Support Back home, my power supply is 850W which should provide enough power, so I thought my motherboard may be faulty or it needs a BIOS update, or something

You can do so either by phone or email. I disable USB sleeping on Windows ( Control Panel > Power Options > Balanced > Change plan settings > Change advanced power setting > USB setting > USB selective suspend setting Round 1. Hope this helps you guys!1.2k Views · View Upvotes Mike ShermanWritten 56w agoThis happened to me too...

The latest driver doesn't fix the problem for me, but version 3.5.2.0 seems to have done the trick, no reg fix needed. #9 | Written by stathis about 2 years ago.