Home > Western Digital > Western Digital Command Error 0132

Western Digital Command Error 0132

I pulled up a command prompt and I accessed the "C" drive, but it was a false positive. Karlsweldt Mobo-fu Master Posts: 20449Joined: Wed Nov 12, 2003 11:57 amLocation: 07438 Top Display posts from previous: All posts1 day7 days2 weeks1 month3 months6 months1 year Sort by AuthorPost timeSubject M. Re-Test Drive 4 Open Drive Failure Cannot communicate with drive. Source

If the error repeats, replace the drive. Commit interval 5 seconds[ 85.990807] EXT3-fs: mounted filesystem with ordered data mode.[ 97.002795] ata1.01: status: { DRDY ERR }[ 97.002837] ata1.01: error: { ABRT }[ 97.025711] ata1.00: configured for UDMA/100[ 97.034414] The failure to complete the test indicates a failed drive. In case you encounter one of the mentioned errors, try fixing it your own, you have the guidelines.

Re-Test Drive 107 Check Sum Error Accumulated test data on the drives is corrupted. It also may be due to a defective connection. Replace your cable and retest. Return to Top Data Lifeguard Tools 2.8 Error Codes Note: If the same error code is encountered more than once after re-testing, please Contact Us for additional assistance. Error code

Please re-test the drive with Data Lifeguard. WD Internal Drives Desktop & Mobile Drives psongman 2011-11-20 07:59:20 UTC #1 HI, I am sure this has been mulled over a few times here but I can't narrow down the The drive may not have been accessed properly possibly due to a bad connection. If this is your first visit, be sure to check out the FAQ.

I guess I just cant justify paying that much to do it. Unfortunately, I can't coax any life out of it anymore. It is the dualie computer in my sig but with 2 GB of RAM and a 300GB Western Digital HDD. This may be due to a media error.

May need to run DLGUDMA to set the drive to a slower speed or replace the IDE cable. This may be due to a media or read/write error. Replace Drive 210 Self Test Incomplete SMART Self Test failed to complete (e.g. -- timed out). Replace the drive if the error repeats.

Data sent between the host computer and the drive has been corrupted. Command Line Switches ... So after a bunch more researching, I decided to try the U12 swap off of my original pcb and the new one from Western Digital. Re-test Drive 140 DRQ TIMEOUT ECC The drive did not properly respond to test commands.

SERVO is data on track location. http://thetechevent.com/western-digital/western-digital-controller-board-replacement.html Please contact the system vendor for the above-mentioned information. There are too many errors detected on this drive to be repaired. Every specific Western Digital Error Status Code 0132 has its own unique causes.

Replace Drive 570 No Recalibration Recalibration command failed. Re-test Drive 162 READY EXPECTED Timeout from checking busy bit. It may also be due to a defective connection. have a peek here The cable is loose, broken, or not plugged in.

Track 0 also holds information about the drive. So then I tried new ribbon cables and tried running it stand alone in the pc and still nothing... The Identify Drive Command has not received an acceptable response from the drive.

Re-test the drive with Data Lifeguard.

The only difference was the year. (Mine said 2004 and the new one said 2006) So I tried that out and same thing happened as the last one. Replace Drive 210 Self Test Incomplete SMART Self Test failed to complete (e.g. -- timed out). Replace the drive if the error repeats. It also may be due to a defective connection.

Post navigation Previous PostPast Tense Errors ExamplesNext PostSnoopy Errori Search for: Proudly powered by WordPress close × Questions Documents More Menu Tweet Western Digital Command Error Code 0132 You are here: It may also happen when the wrong version of diagnostic utility is used. Use the appropriate version. Check This Out Replace the drive if the error repeats.

Check cabling and retest. Drive should be replaced. Replace the drive if the error repeats. Do a test, unplug the drive and see how long it takes for the BIOS screen to get past.

The diagnostics are successful; they complete really quickly.The funny thing is that at bootup (i.e. This may be an anomaly or a defect with the drive. This error can occur on non-Western Digital drives. in our lifetimes!

Drive should be replaced. This error may also appear if the floppy has been infected by a hidden virus. Sense: No additional sense information[ 78.984678] end_request: I/O error, dev sdb, sector 24[ 78.984680] Buffer I/O error on device sdb, logical block 3[ 78.984689] ata1: EH complete[ 78.984770] sd 0:0:1:0: [sdb] Replace Drive 226 Sector Relocation Error Failure to relocate a sector during drive repair.

I took out the CD about another hour later and tried to boot up...l.it came to the Start Windows Normally Screen, and I said what the heck, clicked on it, well,