Home > Western Digital > Western Digital 11-test Cable Error

Western Digital 11-test Cable Error

Replace the drive if the error repeats. Drive should be replaced. Back to top #3 Phantom_KID Phantom_KID Topic Starter Members 8 posts OFFLINE Local time:12:38 AM Posted 14 February 2006 - 11:38 PM i'll try it out Back to top #4 Join Now For immediate help use Live now! http://thetechevent.com/western-digital/western-digital-11-cable-test-write-sector-error.html

The automatic repair feature can attempt a repair if possible. PeteC Donate WindowsBBS Forums > Hardware > PC Hardware > Style Default Contact Us Help Home Top RSS Terms and Rules Forum software by XenForo™ ©2010-2016 XenForo Ltd. the hard disk is accessible when i turned on the computer in the morning or after it's been off for more than about an hour. Drive should be replaced.

Replace the drive if the error repeats. Please ensure that you are not loading any other DOS level files from the floppy prior to running diagnostic utility. cool_ank 2010-07-22 18:09:47 UTC #4 ya did that ... You may also want to reroute your IDE cable away from sources of electronic bus noise such as your CPU, Power Supply, etc.

Drive should be replaced. ECC is a hardware correction technique that corrects errors. Further errors indicate a defective drive. ty for the links pcbugfixer braindead, #11 2009/10/19 pcbugfixer Inactive Joined: 2009/09/28 Messages: 273 Likes Received: 2 Trophy Points: 108 Location: Condell Park (Sydney) NSW, AU Computer Experience: Experienced G'Day

Re-Test Drive 586 DRQ Timeout Data ReQuest Timeout. enabled help you monitor a drive's internal status through diagnostic commands. No Errors 0001-0015 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. As far as your icon, sometimes it vanishes or becomes unreadable.

Check connections and retest. The computer also moves very slowly when the drive is attached The Drive is in warranty but i don't want to loose the imp data in it cool_ank 2010-07-21 18:42:39 UTC Ten or more instances of track information could not be found. Anything else can be done?

Retest after checking the connections. The same utility and the original code used to lock the drive are necessary to unlock this drive. Thanks. I already ruled out a bad CD\DVD or Burn as I also reproduced this issue using two different machines and after verifying the burn was successful.

To run in ATA 66 and ATA100 rates, an Ultra ATA 80 -conductor cable must be used. this contact form This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Drive should be replaced. Replace the drive.

By the end of it, your faces might even hurt from smiling so much! The information file, which holds the data pertaining to this drive, is corrupted or missing. Check cabling and retest. http://thetechevent.com/western-digital/western-digital-cable-test-read-diagnostics-sector-error.html Retest.

The failure to complete the test indicates a failed drive. Replace Drive 207 SMART status failed before the media scan. Check the drive connections.

Test Time: 05:59:17, October 19, 2009 Test Option: EXTENDED TEST Model Number: WDC WD5000BEVT-11ZAT0 Unit Serial Number: WD-WXNX08NC5444 Firmware Number: 01.01A01 Capacity: 500.11 GB SMART Status: FAIL Test Result: ABORT Test

LMan550 2010-01-08 11:31:18 UTC #13 Tek20 wrote: The problem is with Data Lifeguard for Windows version 1.17. ... My problem with my drive is that it keeps dropping off line. Contact System Vendor 221 Test Not Supported Certain older drives do not support certain SMART Self Tests. Re-test Drive 138 Still Busy Timeout Timeout from checking busy bit.

Data request has timed out when writing to the drive. I have the Knack. ** If I haven't replied in 48 hours, please send me a message. which is questionable in this case, since the device is showing up, but not properly ... 1. Check This Out oh i see, that is odd, but its a wd passport which ya.

Retest. End. 8. Drive should be replaced. This may be due to a defect.

Please ensure that you are not loading any other DOS level files from the floppy prior to running diagnostic utility. Retest the drive. Retest after checking the connections. By continuing to use this site, you are agreeing to our use of cookies.

Username Forum Password I've forgotten my password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Privacy Policy

MenuExperts Re-test Drive 143 RANDOM SEEK ERROR Error encountered during random seek. This may be due to a media error. Replace Drive 208 SMART status failed after the media scan.

This may be due to a media or read/write error. Replace Drive 550 Abort Cmd Abort Command. The drive has not responded to the SMART test request. ECC is a hardware correction technique that corrects errors.

Re-test Drive with appropriate diagnostic utility 202 Drive Not Supported Older Western Digital drives are not supported by the diagnostic utility version being used. This may be due to a defect with the drive or a bad connection. It may also happen when the wrong version of diagnostic utility is used. Replace Drive 0009 - 0014 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command.

gkelly 2010-01-19 15:20:45 UTC #18 Yeah it's definitely bizarre. Using the old version of the program, quick test is finding no errors. kevinrs 2010-01-10 07:31:03 UTC #14 I'm having problems with the drive as well, the cable test error was preventing me from even testing the drive though.