Home > Error Code > Lexmark Fax Error Codes

Lexmark Fax Error Codes

Contents

C 4-26 Service Manual manuals4you.comLexmark X342N | Service Manual - Page 99...card. Paper not being picked up check paper tray & pickup rollers Replace rollers if worn smooth or cracked ERROR 21 The exit sensor was not made in time after the input be failing. 202.02 89 xx 0D 202.06 2-16 Service Manual ...Lexmark X342N | Service Manual - Page 39... V 7-9 Fuser assembly, 220 V 7-9 Fuser assembly, 100 V 7-9 Laser/mirror print assembly, X340, X340n, X342n 7-9 Paper feed, rubber tires 7-11 Input #1 sensor ...cable 7-5 Flatbed cover Check This Out

Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers See "Fuser service check...Lexmark X342N | Service Manual - Page 55...are installed correctly and that the toner cartridge is not low on toner. Remove the sensor and the attached cable, ... Remove four screws (A) in the gear train metal cover. 4.

Lexmark Fax Error Codes

Remove the operator panel assembly. Request Quote Error 920 920 Fuser Error indicates the Fuser is below temperature while printing. top, left ,and bottom margins of the MFP. Error messages are displayed if applicable. 7.

Restore Default ATM MENU - Go to "ATM menu" on ... 3-11. Remove rear cover. Don't show me this message again. Lexmark Fax Error E970 Privacy Policy Terms of Use ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.8/ Connection to 0.0.0.8 failed.

Use a small Phillips screwdriver to remove the screw (A) that secures the sensor to the printer frame. 5. Lexmark Error Codes Replace defective cartridge. Scanner ADF separator pad removal 1. Home | My Manuals | Manual Index | Manual Categories Home > Lexmark Manuals > Multifunction Devices > Lexmark X342N > Manual Viewer Lexmark X342N Service Manual Lexmark X342N - Multi

the paper. Fax Error Codes Ricoh POR the MFP, and check each light for proper operation. The ScanBack utility is bundled with the X342n. ...Lexmark X342N | Service Manual - Page 20... 209 locations Yes Not supported Tips on preventing jams You can avoid most paper jams Tray 2.

Lexmark Error Codes

See “Duplex” on page 2-16 Error 24 The defined paper size is too short to print data as formatted. Replace the bump alignment motor Replace bump motor Replace interlock switch Replace System Card Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex Lexmark Fax Error Codes Error 939 RIP Communications Lost Controller Engine Communications Lost The controller board and the engine board cannot communicate with one another. Error Code 700 Error In Fax Transmission I 4-52 Service Manual manuals4you.comLexmark X342N | Service Manual - Page 1257003-XXX 9.

If the jamming continues and the paper is getting damaged inside the printer at the front of the fuser unit: Remove the cartridge and take out the paper that is jammed. http://thetechevent.com/error-code/xfb-error-codes.html before calling your second level support center. Got it, continue to print 2012-2016 ManualsLib.com About Us About ManualsLib Privacy Policy F.A.Q. If the 201 Paper Jam error appears on power up when the main motor attempts to engage and there is no paper jammed in the printer: The main motor assembly on Lexmark Fax Error E-724

right margin equals -8. The pin should enter the tower on the HVPS and depress the cover switch. E-885 Failure to transmit training successfully in V17 modulation scheme. • Select a lower ‘Max Speed’ value under Fax Send settings.• Adjust ‘Transmit Level’.• Check line quality. this contact form eCommerce Solution : k-eCommerce My Account| Cart| Order Status Market Point Search: select Advanced search Read Customer Reviews GSA Contract Schedule Enter Here Need Assistance?

Remove the scanner assembly. Fax Error Code E-713 leaving it free at the opening above the LVPS/HVPS. 5. If ...

To remove the jammed sheet of paper: Open the upper front door.

If you have other tech support questions that are not covered here, send email to [email protected] Printer registration needs to be performed whenever ...mrgn. Print quality will be diminished. T2 Timeout Occurred Due To Loss Of Command/response Synchronization. Repair information ...Lexmark X342N | Service Manual - Page 122...

RIP software Service (No Modem) General engine software failure Action Server firmware problem. While prying the rear cover back, slide the modem card down, and remove the modem card from the MFP. 4-54 Service Manual manuals4you.comLexmark X342N | Service Manual - Page 127... 4-30. card (front, top of card). navigate here I am new to this and do not want to screw this up.

Requires further measurement The printhead (laser scanner) does not contain any serviceable parts. Repair information 4-43Lexmark X342N | Service Manual - Page 116... Just to the right of the back gear, you should see a black plastic flag sticking up through a hole in the black plastic floor of the printer. flatbed cover. 5.

An error occurred that prevented the scanner from sending the scanned document to its destination. cover removal" on page 4-5 for more information. 3. Indicates that the fuser is below standby temperature when the printer is idle. If the setting is not in your driver, you can download the correct Lexmark setup utility from the Lexmark Web site at www.lexmark.com.

Error 920.X and 922.XX may display for a cold fuser. Note: When reattaching the network card, attach the card to the... does not feed into the ADF MFP produces a black page when copying a document. Shop for Lexmark print cartridges Error 32 32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer.

Press Stop ... to 6.93 x 9.84 in. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Carefully remove the 18 and 20 pin ribbon cables (A) from the CCD. 3.

more information. I worden niet als ongevaarlijk aangemerkt. assembly. 6. Unplug the fan from the controller card at J19. 3.